Skip to content

Drain Jetting Toronto

Drain jetting in Toronto strips grease, silt and soft root mats off pipe walls with water at high pressure, leaving the line scoured rather than just punched through. The job is quoted up front, and one call books a plumber in Toronto with the jetter on board.

Licensed plumbers and gas fitters · NSW Lic. 359278C

Last updated September 2026

Plumber working at the hose reels on the back of the ute

When Does a Drain Need Jetting?

A cable machine opens a gap in a blockage; the jetter washes the whole bore. You notice the difference in how long the fix lasts, and it matters most here:

Fat coating the kitchen line

Fat and soap coat the pipe wall over years, narrowing it until scraps catch. A cable pierces the plug; the jet washes the coating off the wall so the line runs full bore again.

Silt and debris in stormwater lines

Sand, leaf litter and runoff sediment settle along the invert, and a scour is the only way to move it out.

Fine roots

Roots that have worked into a joint form a hairy mat, and high-pressure water strips it back cleanly.

Recurring blockages

If a drain has cleared before and blocked again, the wall inside is usually rough or coated, and jetting resets it.

What Does the Jetting Process Involve?

Pressure in a pipe nobody has looked at is a gamble, so the steps never change:

  1. 01

    Check first

    A camera pass shows what's in the line and whether the pipe is sound enough to jet hard. On older runs, that check matters before the trigger is pulled.

  2. 02

    Access the clean-up point

    We work through an inspection opening or grate where one exists, which keeps the job off your garden.

  3. 03

    Scour the line

    The jetter head travels the pipe on a hose, spraying backwards at pressure, flushing grease, silt and root material back toward the access point so they can be pulled out rather than pushed deeper.

  4. 04

    Confirm the result

    Another camera pass or a flow test proves the line is clear end to end, and we show you the difference.

The gear is the same set we carry for every drain job: CCTV camera, jetter, electric eel and pipe locator. If the camera shows a line too fragile or too broken to jet, the job turns into a repair or reline conversation instead, and we talk you through those options before anything starts.

What Drives the Cost of a Jetting Job?

Jetting is priced mostly on reach, meaning how far the head travels before it meets the choke:

  • Where the blockage sits A kitchen line fed from a nearby grate takes less time than a sewer run that has to be located first.
  • What the camera finds Grease scours out in one pass. Roots plus a cracked joint turn the job into a repair conversation, and pipe relining is sometimes the smarter spend.
  • Access An opening at the boundary gets the hose in straight away; a line without one adds setup time.

We provide up-front, honest quotes that will always match the final price, should you decide to go ahead. You decide with the footage and the price both in hand.

Jetting Around This Town's Housing

The older pipe stock sets the work

Houses from the early subdivision years still drain through brittle earthenware, and those lines collect scale and catch roots at every joint. A scour that leaves the wall clean buys real time compared with a cable poke.

Stormwater lines on the low streets

Foreshore-side runs gather silt and leaf litter through the year, and when a big storm fills the Lake Macquarie catchment, a half-silted line is the one that surcharges first. A jet ahead of storm season is affordable protection on those blocks.

Kitchen drains in the older cottages by the water

Grease builds slowly on those runs, and jetting restores the full bore without touching the pipe itself.

"We talked through the options of our blocked kitchen sink drain (not just an s bend problem) and came to the perfect long term solution at a reasonable price." Debbie

Plumber working a drain-clearing machine

When We're Not the Right Call

A collapsed or badly broken pipe can't be scoured back to life, and jetting it would be throwing good money after bad. That's why the camera comes first: if the footage shows structural damage, we quote a repair or a reline instead. And if the blockage sits in the water authority's main out in the street, that one goes to their faults line.

Plumber pulling fittings from the ute drawers

Drain Jetting Questions

Can jetting damage older earthenware pipes?

Not with the camera going in first. We check the line first, so sections that are cracked or brittle get a gentler method or a repair plan instead of full pressure. The jet only runs hard where the pipe is sound.

How often should a drain be jetted?

It depends on the pipe. A kitchen line that greases up might want it every year or two, while a root-affected clay line on an older block usually needs the pipe itself dealt with, not just another scour.

Does jetting clear roots as well as grease?

It strips fine root growth off pipe walls very effectively. Thick woody roots that have grown through a cracked joint are a different job, and the footage sorts one from the other before the hose goes in.

Do you jet stormwater lines too?

Yes. Silt and leaf litter build up in stormwater lines across the suburb, and the low foreshore streets feel it first when a downpour hits the catchment. A scour before storm season clears the run.

Book Your Jetter Today

Toronto Plumbing Co runs jetting across Toronto and the western shore as part of a full blocked drains service, alongside CCTV drain inspections, sewer clearing and tree root removal. Call (02) 4093 0558 or send the form below. Available 24/7, you see a fixed figure ahead of any work, and every job carries our 365-day warranty on all work.

Call (02) 4093 0558

Request a callback

Leave a name and number and a plumber will ring you back.

We use your details only to call you back about this job. See our privacy policy.

Call (02) 4093 0558 Get a quote